In less than a minute, a single cold start without proper preheating can produce more wear on your piston aircraft engine than 500 hours of normal cruise operation. If it's cold enough, a single cold start can cause the catastrophic destruction of an engine shortly after takeoff. This is serious stuff, folks! AVweb's Mike Busch tells you what you need to know to make it through the cold-weather flying season without damaging your expensive powerplant.
June 20, 1999
preheating is something most of us first learned about in private pilot ground school, it
remains a subject that's poorly understood even by experienced pilots and aircraft owners.
There are a lot of misconceptions about why preheating is important, when it's necessary,
and how it should be accomplished. But, by the time you've finished this article, I
promise that you'll be an expert on the subject.
The first question that invariably comes up is how cold it has to be before preheating
is necessary. Of course, there's no hard and fast answer to that question. The degree to
which a cold start will damage an engine depends on a variety of things, including the
type of engine, its age and condition, what sort of cylinders it has (steel vs. chrome),
and what kind of oil is being used.
Interestingly enough, a brand new factory reman is considerably more vulnerable to cold
start damage than a tired old engine near TBO. Surprised? Stay tuned and you'll find out
As a general rule, we consider any start in which the engine is cold-soaked to a
temperature below freezing (32°F or 0°C) to be a "cold start," and any start
below about 20°F (-7°C) to be nothing short of a capital offense against your
powerplant. The colder the temperature, the worse the crime.
Most pilots seem to think that the main reason cold starts are bad for engines is that
the engine oil is thick and viscous and doesn't flow well. Since it takes longer for oil
pressure to come up when the oil is cold, the engine sustains excess wear in the early
seconds after start because of inadequate lubrication. That's what my primary CFI taught
me when I was studying for my private ticket 35 years ago.
That might have had some validity back then, but not today. Nearly everyone who flies
in cold weather nowadays uses multiviscosity oil such as Shell 15W-50 or Chevron 20W-50,
and those oils flow extremely well even at 0°F (-18°C) or less.
Consequently, pilots who use multivis oils quickly observe that their oil pressure
comes up quickly after starting even in cold weather, and they figure that therefore
everything's okay. Big mistake!
Crankshaft bearing clearance.
The real culprit in cold-start damage is the fact that our aircraft engines are made of
dissimilar metals with radically different expansion coefficients. The crankcase, pistons
and cylinder heads of your engine are made from aluminum alloy, while the crankshaft,
camshaft, connecting rods and cylinder barrels are made from steel. When heated, aluminum
expands about twice as much as steel. Likewise, when cooled, aluminum contracts about
twice as much as steel. And, therein lies the problem.
Consider your steel crankshaft, which is suspended by thin bearing shells supported by
a cast aluminum crankcase. As the engine gets colder, all of its parts shrink in size, but
the aluminum case shrinks twice as much as the steel crankshaft running through it. The
result is that the colder the temperature, the smaller the clearance between the bearing
shells and the crankshaft. That clearance is where the oil goes to lubricate the bearings
and prevent metal-to-metal contact. If there's not enough clearance, then there's no room
for the oil, regardless how high the oil pressure gauge reads.
How significant is this problem. Well, take the TCM IO-520-series engines used in many
Beech and Cessna singles and twins, for example. The IO-520 overhaul manual lists the
minimum crankshaft bearing clearance as 0.0018 inch (that's 1.8 thousandths) at normal
What happens to that clearance when you start cooling the engine down? TCM doesn't say.
But tests performed in 1984 by Tanis Aircraft Services
in Glenwood, Minn. (where it gets mighty cold) indicated that an IO-520 loses 0.002 inch
(2.0 thousandths) of crankshaft bearing clearance at -20°F. An engine built to TCM's
minimum specified bearing fit at room temperature would actually have negative bearing
clearance at -20°F-in other words, the crankshaft would be seized tight!
You've probably noticed how difficult it is to pull the prop through by hand before
starting in cold weather. Now you know why. It's not that the oil is thick (because if you
use multivis oil, it's not). It's that the clearance between the crankshaft and bearings
is tighter than normal. If it's cold enough, you might not be able to pull the prop
through at all.
Start an engine in this condition and you're likely to experience accelerated bearing
wear and possible damage to the crankshaft journals in the first minute or two of engine
operation. If bearing clearances are small enough, it's even possible for the bearing
shells to shift in their saddles-a so-called "spun bearing-misaligning the oil feed
holes and starving the bearing from lubricating oil.
Ironically, this problem is at its worst with a fresh-from-the-factory engine built to
the tightest new-engine tolerances. A tired, loose, high-time engine with worn bearings
(or an engine with low time since a sloppy bargain-basement overhaul) might well have
plenty of clearance even at subzero temperatures.
But, even if your engine is approaching TBO, you can't afford to be complacent about
cold starts. That's because inadequate bearing clearance is only one of several evils
associated with cold starting.
Consider what happens to your pistons and cylinders when you cold-start an engine.
Here, the situation is the opposite of the one we just talked about: instead of a steel
crank inside an aluminum case, we have an aluminum piston inside of a steel cylinder
barrel. So the clearance situation is reversed: piston-to-cylinder fit is loose when the
engine in cold, and tightens up as the engine comes up to full operating temperature.
(This is why compression tests are normally done when the engine is hot.)
So why would cold starting be a problem for the engine's top end? Several reasons.
When an engine is started cold and comes up to temperature, the piston and cylinder
barrel don't warm up at the same rate. The piston heats up very rapidly after start, while
the cylinder barrel may take quite a long time to warm up. Why? Well, for one thing, the
piston is small and light, while the cylinder his big and heavy, so when both are exposed
to the heat of combustion, the piston heats up a great deal faster. In addition, the
cylinder has a very effective mechanism for shedding heat-it's covered with cooling fins
bathed in what is presumably frigid air-while the piston's only real cooling comes from
the splash of engine oil, and the low RPMs of start and idle there's not a whole lot of
splash oil available.
The result is that the piston expands to its full operating dimension quite quickly
after start, while the cylinder takes a lot more time to expand to its full operating
diameter. The colder the OAT, the longer it takes for the cylinder to reach operating
temperature. The result is that although the fit of the piston in the cylinder is quite
loose when the engine is cold, it may quickly become tighter than normal shortly after
starting when the piston has come up to temperature but the cylinder still has a long way
to go. If it's cold enough, the piston-to-cylinder clearance can actually wind up going to
zero, resulting in metal-to-metal scuffing between the piston and cylinder barrel.
This problem is made worse by the fact that most cylinder barrels are designed with a
taper or "choke" in the top one-third of piston travel. This is done to
pre-compensate the barrel for the fact that, as the engine comes up to operating
temperature, the top of the cylinder (where the combustion process takes place) is a lot
hotter than the bottom of the cylinder, and therefore expands considerably more. If
cylinders were perfectly cylindrical at room temperature, then they'd become flared at the
top when the engine was hot, resulting in loose fit between the piston and cylinder barrel
right where a tight fit is most needed-at top dead center. By giving the cylinder barrel a
slight taper at the top when at room temperature, the cylinder winds up being cylindrical
at operating temperature.
When an engine is started in cold weather, the cylinder choke starts out considerably
greater than normal. After start, the piston starts being repetitively forced up into the
choked-down area at the top of the stroke. As the piston quickly comes up to temperature
but the cylinder is still relatively cold, it's easy to see how severe scuffing can occur
at the top of stroke.
As you can see from this discussion, warming up the engine oil is definitely not enough
to avoid cold-start damage. All the warm oil in the world won't help if the
crank-to-bearing or piston-to-cylinder clearances go to zero. To avoid this, it's
essential for a preheat to warm up the crankcase and the cylinder barrels (especially the
top of the cylinder barrels near where they mate to the heads).
The best way to accomplish this is to put the airplane in a heated hangar overnight.
Why? Because this preheats every part of the airplane to an even temperature. After 8 to
12 hours in a 40°F hangar, the oil is at 40°F, the case is at 40°F, the cylinder heads
are at 40°F, the gyro instruments are at 40°F (gyros have their own cold-starting
problems, by the way), the windshield is at 40°F (so it won't fog up the minute you
exhale), and even the pilot's seat is as 40°F (which solves another problem).
I'm based on the California coast where the weather hardly ever gets below freezing,
but when I travel to the cold country, I always try my best to use the
overnight-in-a-heated-hangar method of preheating. Most FBOs seem to charge anywhere
between $20 and $50 to store my 310 in their heated hangar overnight. Even at $50, I
figure it's quite a bargain compared to the alternative (accelerated wear of my two
expensive TSIO-520 engines).
If I'll be staying at a cold-weather airport for awhile, I'm often too much of a
skinflint to pay for the airplane to be hangared for the whole duration. Instead, I'll
arrange with the FBO to pull the airplane into the heated hangar the night before my
scheduled departure. If it's really, really cold out on the morning of departure, I've
been known to preflight the airplane in the hangar, climb into the cockpit, secure the
door, and then have the line crew open the hangar door and tow the airplane out onto the
ramp with me in it. As soon as they unhook the tug, I start the engines before they've had
a chance to get cold-soaked.
Short of overnight in a heated hangar, the best preheating method is a multipoint
electric heating system that has individual heating elements attached to the oil pan, the
crankcase, and each cylinder. By plugging such a system into 115V or 230V power a few
hours before departure (overnight is even better), you can at least be assured of warm
cylinders, a warm case, and warm oil when you start up.
Tanis TAS100 system.
The best-known multipoint electric preheating systems come from Tanis Aircraft Services in Glenwood, Minn. The Tanis
TAS100-series systems cost about $500 for a six-cylinder engine and consist of eight
electric heating elements connected by a wiring harness. Six 50-watt cylinder heaters
screw into the threaded CHT-probe bosses in each cylinder head. A flat silicone rubber
heating pad is glued to the crankcase with high-temp RTV, and another is glued to the
bottom of the oil pan. The wiring harness terminates at an ordinary AC plug that is
usually mounted near the oil filler door in the cowling. You simply run an extension cord
out to the airplane, plug in the preheating system, and let it cook for a few hours.
Although the Tanis TAS100 is a terrific preheating system, one drawback is that its
cylinder heaters displace the normal CHT probe. One solution is to change to a
spark-plug-gasket-type CHT probe. Another is to use a combined heater/probe element
available from Tanis, but this makes the system more expensive, particularly if you have
probe-per-cylinder EGT/CHT instrumentation such as a GEM or JPI 700.
Reiff HOTBANDD system.
In 1992, Reiff Corporation of Delafield,
Wisc. entered the multipoint electric preheating market with their novel
"HOTBANDD" system. In lieu of cylinder head heaters, the Reiff system uses
50-watt heating elements mounted on large stainless steel clamps that mount on the
non-finned portion of each cylinder barrel. As a result, there's no interference with
existing CHT instrumentation. The Reiff system also includes an oil pan heater, but not a
crankcase heater (the theory presumably being that the crankcase receives sufficient heat
by conduction from the oil pan and cylinder heaters). A six-cylinder Reiff system sells
for about $400.
Tanis TAS400 heated rocker gaskets.
Not to be outdone, Tanis recently came out with a
new TAS400 preheating system. In lieu of the CHT-boss heating elements, the new system
uses a "heated rocker gasket" which fits between each cylinder head and rocker
cover, and applies heat directly to the cylinder head. The TAS400 is a significant
improvement over the TAS100 system in a couple of different ways. Not only does it solve
the CHT-probe interference problem, but it also applies heat evenly to the full
circumference of the cylinder head, rather than applying it all at a single point.
Both the new Tanis TAS400 system and the
Reiff HOTBANDD system are capable of providing an
excellent preheat in a couple of hours. We do not recommend cheaper electric systems that
heat only the oil pan. As you now know, heating the cylinders and case is absolutely
Insulated engine and prop covers
by Kennon Aircraft Covers.
If the temperature is not too frigid and the aircraft is being preheated in a
tee-hangar or other protected area, then a multipoint electric heating system is all you
need to do the job. But if it's really cold, or if you have to preheat outside on an
exposed ramp (particularly if it's windy), then you also need some means of insulating the
engine compartment and keeping most of the heat from escaping.
At the very minimum, you'll need an insulated engine cover. Although you may be able to
make do with a quilted blanket, custom-fitted insulated covers are available from
Kennon Aircraft Covers in Sheridan, Wyo., as well as from both
Reiff and Tanis
and a few other firms.
In intense cold or windy conditions, the propeller becomes a major source of heat loss
during preheating. Kennon,
Reiff and Tanis
all offer insulated propeller and spinner covers to solve this problem. Figure about $300
for a good insulated engine cover, and $100 more to cover the prop and spinner.
Another compelling advantage of insulated engine and prop covers is that using them may
eliminate the need for a preheat altogether if you're going to be making a quick-turn. By
installing the covers promptly after shutting down, engine heat can be retained for three
or four hours even when the airplane is parked outside on a cold, windy tiedown.
If you hangar your airplane and use an insulated engine cover, a single-point electric
heater can provide an adequate preheat if it is given enough time to do so (e.g.,
overnight). A simple oil pan heater can do the trick, and even a couple of 100-watt light
bulbs stuck up the cowl flaps may suffice if the engine compartment is well covered.
Kennon offers a novel variation on this theme, consisting of a pair of electrically
heated plates velcroed to the inside of cowl plugs. Combined with a good insulated engine
cover and possibly an oil sump heater, this can do a good job of keeping the engine warm
in all but the most frigid conditions.
These approaches work fine so long as you have plenty of time to preheat, but don't
expect them to heat a cold-soaked engine to safe starting temperature in an hour or two.
For that, you'll definitely need a multipoint electrical heating system, or a forced-air
There has been considerable controversy about whether or not it's a good idea to leave
an electric preheating system plugged in continuously when the airplane isn't flying. Both
TCM and Shell have published warnings against leaving engine-mounted electric preheaters
on for more than 24 hours prior to flight. However, these cautions are really applicable
primarily to single-point heaters such as oil pan heaters.
The concern of TCM and Shell is that heating the oil pan will cause moisture to
evaporate from the oil sump and then condense on cool engine components such as the
camshaft, crankshaft or cylinder walls, resulting in accelerated corrosion of those parts.
However, if the entire engine is heated uniformly by means of a multipoint heating system,
or because the engine and propeller are covered with insulated engine and prop covers,
such condensation is very unlikely to occur.
In fact, using an insulated cover and a multipoint preheating system that is plugged in
continuously is one of the most effective methods of eliminating internal engine
corrosion, particularly if the aircraft is kept in an unheated hangar rather than
outdoors. If the entire engine is maintained above the dewpoint, condensation simply
Herman-Nelson forced-air preheater.
Most FBOs in the cold country use large forced-air preheating units like those
manufactured by Aerotech-Herman-Nelson in
Winnipeg, Canada. Smaller hot air heaters fired by propane, kerosene or gasoline are also
available from a number of sources, including Kennon Aircraft
Forced-air preheating can do an effective job, provided the machine has sufficient BTU
output for the job (some small propane-fired heaters simply don't), and the machine is
left hooked to the airplane for enough time to heat the engine thoroughly. Unfortunately,
if you're depending on an FBO for a hot-air preheat one chilly morning, chances are a
bunch of other pilots are, too. Unless the FBO is willing to devote sufficient time to
preheating your aircraft (and how long that is depends on both the capacity of the heater
and the OAT), you may wind up with a partially-heated engine that has hot spots and cold
How can you tell whether you've received an adequate preheat? It's not easy, but if you
can manage to get your hand inside the engine compartment and if all the rocker covers and
the crankcase feel warm to the touch, you're probably okay.